Top 10 common forklift accidents ， forklift operation should pay attention to these issues ！.

Don't ignore the forklift at the workplace. If the procedure is bad, there will certainly be significant accidents in mins, and there are numerous crashes including forklifts.

Case 1: The forklift freight blocked the chauffeur's sight, and the person ahead could not be located, causing a rolling accident.
Instance 2: In order to keep the balance of the forklift when lifting heavy goods, the employees used their body weight as the weight, which almost caused casualties.
Situation 3: The size of the forklift cargo exceeds the allowable width of the route and hangs on the roadside rack, which nearly triggers an mishap.
Situation 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the employees unlawfully, the forklift motorist does not wear the seat belt, the forklift lifter falls and the chauffeur is squashed when the forklift rolls over.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must take note of these issues ：.

Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that prevent the safety of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift starts with a lots, the chauffeur needs to initially confirm that the load is stable and trusted.
4. The start must be slow and stable.

Driving.
1. When driving, the elevation in between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole should be tilted backward. .
2. Do not lift the fork too expensive when driving. When going into and leaving the job site or while driving, beware that there will certainly be no obstacles in the sky. When the tons is traveling, the fork must not be elevated too high, which will affect the security of the forklift. .
3. After unloading, the fork should be reduced to the typical driving position prior to driving. .
4. When turning, if there are pedestrians or cars nearby, the driving signal needs to be issued initially. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to shed lateral security and topple. .
5. When the forklift is downhill, it is strictly prohibited to turn off the flame and slide, and it is forbidden to brake all of a sudden while driving with lots unless there are special circumstances.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and should maintain a certain safety distance from the automobile ahead. .
7. When the forklift is running, the lots needs to remain in the most affordable position that does not impede the driving, and the gantry must be properly slanted back. The tons will not be raised except when piling or filling. .
8. The height of the lots have to not obstruct the vehicle driver's sight. In unique circumstances, when the thing influences the forward vision, drive at a low rate when turning around.
9. It is restricted to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving rate of the forklift in the manufacturing facility location is 5 km/h, and it must drive safely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for employees to base on the fork to hold items and play a balancing function. .
12. If problems are found, they will be repaired and reported in a timely way, and they will never ever run with ailments or hide them.

filling and discharging.
1. When fork-loading things, the range between both forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the thing should protest the rack. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In unique scenarios, safety indication should be established to remind surrounding pedestrians. .
3. In the process of loading and dumping items, the forklift should be stopped with the brake. .
4. The speed of the vehicle should be slow-moving and stable. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled objects and injure individuals. .
5. When utilizing a fork to fork the goods, the fork should be as deep as possible under the lots, and it must be kept in mind that the fork tip should not touch other items or items. The tons needs to be stabilized with very little back tilt of the gantry to ensure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is reduced to allow for simple positioning of the lots and extraction of the forks. .
6. It is forbidden to fork items at high speed and hit tough things with the fork head. .
7. When the forklift is working, it is restricted for individuals to loaf the fork, so as to stay clear of the collapse of the goods and harm individuals. .
8. Overloading is forbidden, and it is restricted to make use of forks Stand-on Electric Pallet Stacker to lift personnel to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to make use of the brake inertia to slide, put, round or roll things. .
10. It is not permitted to make use of forks to select, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Prior to leaving the forklift, you should unload the goods or reduced the fork framework.
2. Pull the parking brake take care of to dead or depress the emergency brake switch.
3. The engine is switched off and the power is cut off. (Except for unique scenarios, such as the chauffeur does not leave the vehicle's view and does not go beyond 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift operation, the appearance should be examined, and gas, lubricating oil and cooling water must be included.
2. Check the security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are total and efficient.
4. During the procedure of the forklift, examine whether the pressure and temperature level are normal.
5. After the forklift is running, the outside leak needs to likewise be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You need to examine before leaving the automobile;.
2. When you come across a person before you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the nadir of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be as well sharp to stop the tendency of " cost-free switching";.
6. Adding and down the incline should be slow and uniform, and no switching on the incline is allowed.
7. Do not drive throughout the slope. When the gradient is more Stand-on Electric Pallet Stacker than 10%, the lorry ought to be driven in reverse when going downhill;.
8. When the forklift personnel lug the goods and progress, if they encounter big or hefty goods and most likely to the driver's line of sight, they need to take the turning around exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Solitary fork procedure is not allowed.
2. It is not allowed to raise the goods for long distance driving.
3. It is not permitted to pick up the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not allowed to use inertia pressure to get the goods.
6. It is not allowed to make use of stopping pressure to expatriation round or easy-to-roll items.
7. It is not permitted to bring people to service the pallet or fork, and it is strictly restricted to stand under the fork after the fork is increased.
8. Do not drive laterally on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Contours, narrow roads, train crossings;.
2. Sections with a longitudinal incline above 5%.
3. When there is an challenge on one side of the road, the opposite side of the section with the same length as the obstacle need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844